Thursday, September 10, 2015

Common errors and solutions about Galletto 1260 ECU flashing cable

Galletto 1260 is an easy-to-use ECU programmer flash cable.There are still some problems when we use the galletto 1260 ECU flash cable.Bellow obd2repair will tell you some common  error and sollutions  we usually meet .

Galletto 1260 ECU flashing cable


Error 1: "Turn off dash, wait 10s then turn on" 

Problem: Installing EOBD1260 on Windows 7 to remap Honda Civic V2.2 ECU edc16 c31, after click write ECU data button, the system displays an error message: "Turn off dash, wait 10s then turn on". 

Solution: Galletto 1260 requires a minimum car battery voltage to operate properly. Otherwise it will fail to read ECU. Make sure your battery is fully charged. Besides, better to install EOBD1260 software on Win XP system. 

Error 2: “Speed Change”

Problem: When trying to read ECU of Audi A3 1.8T 180hp 2002 ECU with 1260, the Galletto display an error message “SPEED CHANGE”. It is the ME751 or ME755 29F400BB 29F800BB, in several places I read say the ECU's 180hp is 29F800BB I tried to read with the driver ME751 29F400, but the error occurred SK1-SeedKey error. 

Solution: You cannot change the speed in clone galletto 1260. Pull the ECU out of the cat and try on the bench. If it doesn’t work on the bench, look for other tuners, like KESS V2, FgTech Galletto 4 master that won’t kill your car.  

Error 3: Cannot read ECU

Problem: Follow the instruction on video to install the EOBD1260 software, try both on Windows XP and Windows 7, but still fail to get the ECU read. 

Solution: The galletto 1260 is aimed at the Bosch EDC16C31 ecu which stamped on the label outside the ECU. If you want to program other ECUs, this cable will not work. If galletto is able to program your ECU, then the driver is faulty or misconfigured or the cable is bad or user error. 
Make sure you setup the cable to use com1 under derives in windows XP. 
Make sure you select the appropriate vehicle. 
Make sure the drivers are good. Connect the cable to the laptop away from the car and install the latest drivers.

Error 4: Laptop issue 

Problem: Plug the galletto 1260 cable into the vehicle OBD port, the red light flashes, then connect the USB to a rather old laptop and configure the device. When try to read ECU, the system report an error after 4 minutes. 

Solution: Make sure you use the same port on the laptop that you first used when installing EOBD1260. You probably need to install the latest FTDI drivers. 

Error 5: "ERRORE SET_ECU" 

Problem: After install the FTDI drivers, trying to ECU ID the program starts to read but nothing other happens. The process stands at 0 % and after some minutes the error "ERRORE SET_ECU" appears. 

Solution: Make sure the driver is correct installed and the COM port is set to COM1. 

Error 6: REMOTE TO MASS PIN 24 FLASH 

Problem: When try to read out Alfa 2.5V6 ME 2.1 ECU, the system display error message: “ATTENSTION BEFORE TO CONTINUE:REMOTE FEEDING,PUT PIN 24 FLASH EPROM TO MASS GIVE FEEDING AND REMOTE TO MASS PIN 24 FLASH, END TO CONTINUE. SEE THE PDF FILE IN FOLDER DECOMENT” 

Solution: Set the COM1 on windows. Need to connect PIN 24 on the ECU itself to the ground. Not OBD pin. Look at ECU, there are 2 big connectors. You need to find the right connector and then plant a wire on pin 24 and ground it.


This article is compiled by www OBD2repair com, if you have any advice on it, pls feel free to contact OBD2repair - China OBD2 repair Tool Automotive Diagnostic Tools Car Key Programmer OBD2 ECU chip tuning tool Center.

ADD:1102A,DongMing Business Bldg, Longhua  new district, Shenzhen 518113,China
TEL :+86-755-29438109
Email:       sales03@eobdtool.com
Skype:obd2repair / eobdscan1
Website:   www.obd2repair.com
Facebook: Misha Liang

Please Give Us Your 1 Minute In Sharing This Post!
SOCIALIZE IT →
FOLLOW US →
SHARE IT →
Powered By: OBD2REPAIR.Com

6 comments:

  1. http://img98.rajce.idnes.cz/d9802/11/11009/11009527_7755993756ec475320bf845e18abde37/images/Beznzvu_1.jpg?ver=0

    what is wrong? thx

    ReplyDelete
    Replies
    1. Common Errors And Solutions About Galletto 1260 Ecu Flashing Cable ~ Galletto 1260 >>>>> Download Now

      >>>>> Download Full

      Common Errors And Solutions About Galletto 1260 Ecu Flashing Cable ~ Galletto 1260 >>>>> Download LINK

      >>>>> Download Now

      Common Errors And Solutions About Galletto 1260 Ecu Flashing Cable ~ Galletto 1260 >>>>> Download Full

      >>>>> Download LINK 0a

      Delete
  2. and what mean error 9 ?
    Thanks

    ReplyDelete
  3. Common Errors And Solutions About Galletto 1260 Ecu Flashing Cable ~ Galletto 1260 >>>>> Download Now

    >>>>> Download Full

    Common Errors And Solutions About Galletto 1260 Ecu Flashing Cable ~ Galletto 1260 >>>>> Download LINK

    >>>>> Download Now

    Common Errors And Solutions About Galletto 1260 Ecu Flashing Cable ~ Galletto 1260 >>>>> Download Full

    >>>>> Download LINK

    ReplyDelete
  4. Error help`? flash bin tune. And i get in the end error message on 1260 software [100% 83s)
    Closing ECU...errore invio END

    Any tip?

    ReplyDelete